Tecnología para tu próximo proyecto

SOPTO’s 16 PON port pizza-box EPON OLT provides 1 USB interface, 4GE(copper) and 4GE optical interface, 2*10Gb uplink interface, and 16 EPON ports for downstream. It can support 1024 ONUs under 1:64 splitter ratio.

SOPTO Data GPON ONU series Includes Wifi or not is one of the GPON optical network unit design to meet the requirement of the broadband access network. It applies in FTTH/FTTO to provide the data, video service based on the GPON network.

SOPTO’s CATV GPON ONU series is fiber to the home multi service access GPON ONU. It’s based on the mature, stable, high cost performance GPON technology and has gigabit Ethernet switching, WDM and HFC technology.Single Fiber series adopts single fiber WDM technology with downlink wavelength 1550nm and 1490nm, uplink wavelength 1310nm. It only needs one‐core fiber to transmit data and CATV service.

SOPTO Data Epon ONU series Includes Wifi or not is one of the EPON optical network unit design to meet the requirement of the broadband access network. It apply in FTTH/FTTO to provide the data, video service based on the EPON network.

CATV EPON ONU series is fiber to the home multi-service access EPON ONU. It’s based on the mature, stable, high cost performance EPON technology and has gigabit Ethernet switching, WDM and HFC technology.Single Fiber series adopts single fiber WDM technology with downlink wavelength 1550nm and 1490nm, uplink wavelength 1310nm. Dual Fiber series adopts dual fiber WDM technology with downlink wavelength 1490nm, uplink wavelength 1310nm .

Ethernet Over Cable is deployed in the existing CATV HFC network to carry out internet and CATV bidirectional networking reconstruction. It consists of master and slave. EOC Master is usually resided at optical node.

Ethernet Over Cable is deployed in the existing CATV HFC network to carry out internet and CATV bidirectional networking reconstruction. It consists of master and slave. EOC Slave is usually resided at subscribers’home.

The product of indoor type is a high-power ceiling mounted AP with double frequency. This AP product adopts optimized radio frequency emission technology, provides broader coverage area and higher signal quality, meets the standards of 802.11b/g/n and 802.11ac protocol, supports installment of ceiling mounted, wall mounted and keel installation,supports 48V POE power supply, when providing high emission power, the overall power consumption is still low.

Optical Transmitter is specially designed for overlay slot system. It supports up to 32 IPQAM frequency point spots. As the first company to introduce overlay frequency point spot system, SOPTO optimizes performance. SOPTO can provide different types of Optical Transmitter with internal or external modulation. Generally, the internal type can only be transmitted within 30km .The external type can transmit 100km

Erbium Doped Fiber Amplifier (EDFA) can be used in HFC system about CATV and SDH system in Telecom. It can provide preamplification, line amplifier and power amplifier. In multiple network applications, it is with good operation record, high stability and

Optical receiver is designed for TV signal transmission of FTTH system, it can work in lower optical power and achieve good CNR, which meets the requirement of analog and digital television transmission. With compact design, Optical receiver can reach to

The 19-inch network cabinet is applied to computer network integrated engineering, building wiring, telecommunications, radio and sound engineering, intelligent community, school, government and other economic and large and medium-sized wiring projects. The equipment can be used to place active and passive devices such as switches, routers, servers, 19-inch optical fiber terminal boxes, etc. Sopto provide 12U,14U,18U,22U,27U,32U 37U,42U 47U network cabinets with glass door or mesh front door.

The wall-mounted cabinet is small in size and saves space. It is suitable for small-scale integrated wiring projects such as building wiring, intelligent community, schools and buildings. SOPTO provide 4U,6U,9U,12U,15U and 18U wall mounted network Cabinet.

This visual fault locator uses a 650nm wavelength semiconductor laser to inject visible red light into the fiber. By observing the light leakage position on the fiber under test, the position of the fiber fault point can be easily and accurately determined. This product is used in conjunction with the OTDR to compensate for the shortcomings of the OTDR near-end blind zone. In addition, in the multi-core cable, ribbon fiber test, can be used as a core control

Optical light source is divided into intelligent and basic type, which can provide high-stability optical signals with multiple wavelengths. It can be used together with our optical power meter series products to easily and accurately measure fiber loss, and is an effective length-building optical fiber transmission network. Ideal for local and optical networks. Accurately identify fiber by providing a modulated optical signal for use with our fiber identifiers

Optic Fiber Identifiers are a must-have tool for fiber maintenance for lossless fiber identification and can be detected anywhere in single mode and multimode fiber. During maintenance, installation, cabling, and recovery, it is often necessary to find and separate a specific fiber without interrupting the service, and to inject 1310nm or 1550nm band modulated (270Hz, 1KHz, 2KHz) signals into the fiber through a port. Use the recognizer to identify it on the line.

Optical Variable Attenuator is an optical test instrument for the measurement of optical fiber systems, signal attenuation of short-range communication systems, and system experiments. It is capable of continuously variable attenuation of optical signals. Widely used in digital and analog modulation systems for communication equipment

SOPTO’s Optical Power Meter integrates the handheld optical power meter and the intelligent optical power meter in one unit. It can be used for the absolute power measurement and relative measurement of the link loss in dB. Its compact size, friendly operation interface, broad power measurement range, high precision and brand-new user automatic calibration function and high performance in application makes it an ideal tool for optical fiber network.

PON optical power meter- intelligent and economical. Its working mode is to extract a small part of the optical signal online at any position in the PON network, and then measure the whole FTTx service opening, maintenance and detection stage, reliably verify and ensure the network communication requirements are met.3213 Series PON Optical Power Meter target at the FTTx application and maintenance. It is able to simultaneously test and estimate the signals of the voice, data and video

SPTK-3302 Series Optical Time Domain Reflectometer (OTDR) is an intelligent meter of a new generation for the detection of fiber communications systems.SPTK-3302 Series OTDR uses 1625nm wavelength to scan and analyze the access point and proceed online testing with optical filter, and will not disturb the service.

OTDR Launch Cable Box is designed to aid in the testing of fiber optic cable when using an OTDR. The OTDR Launch Fiber box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.

Fiber optic cleaver is used to cut the fiberglass for fusion splicing, also ideal for preparing fiber for pre-polished connectors to make a good end face, and it is very important in the fiber splicing process, usually it works together with the fusion splicer to meet the end needs.

FTTH high-precision fusion splicer with its sleek shape and reliable quality, is a precision, durable and convenient fiber construction instrument specially designed for installation, operation and fiber network maintenance. It is widely used in the field of optical communication such as construction, inspection and maintenance of fiber cable.

Fiber optic cleaner is an essential accessory to maintain and guarantee good quality of fiber optic connection. It is a high-performance non-alcohol cleaner designed specifically to clean fibre end faces of any male fibre connector.The Fiber End-Face Cleaning Pen SC is a high-performance device designed for cleaning the ferrule end faces of SC and FC connectors.